SP1F/DSP1F cutting parameter: 1 flutes/O flute milling bit for acrylic/wood/aluminium
| Recommend Cutting Parameters( Single Flute SP1F/DSP1F Serials) | |||||||||
| Cutting Diameter | Soft Wood and Plastic | Acrylic | Aluminium and Copper | ||||||
| RPM(min-1) | Feed Speed ( mm/min) |
Ap(mm) | RPM(min-1) | Feed Speed ( mm/min) |
Ap(mm) | RPM(min-1) | Feed Speed ( mm/min) |
Ap(mm) | |
| 1mm | 14000-22000 | 800-1200 | 1-1.5 | 14000-22000 | 800-1200 | 1-1.5 | 14000-18000 | 600-900 | • Slotting: Ap ≤ 0.5 × D • Side Milling: Ap ≤ 1.5 × D |
| 1.5mm | 14000-22000 | 1000-1200 | 1.5-2.2 | 14000-22000 | 1000-1200 | 1.5-2.2 | 14000-18000 | 800-1000 | |
| 2mm | 14000-22000 | 1100-1300 | 2-3 | 14000-22000 | 1100-1300 | 2-3 | 14000-18000 | 800-1000 | |
| 2.5mm | 14000-22000 | 1200-1400 | 2.5-3.8 | 14000-22000 | 1200-1400 | 2.5-3.8 | 14000-18000 | 800-1100 | |
| 3.1mm | 14000-22000 | 1400-2000 | 3.1-4.6 | 14000-22000 | 1400-2000 | 3.1-4.6 | 14000-18000 | 900-1200 | |
| 4mm | 14000-20000 | 2000-3500 | 4-6 | 14000-20000 | 2000-3500 | 4-6 | 14000-18000 | 1300-1800 | |
| 5mm | 12000-18000 | 2400-4000 | 5-7.5 | 12000-18000 | 2400-4000 | 5-7.5 | 12000-16000 | 1300-1800 | |
| 6mm | 12000-18000 | 3500-5000 | 6-9 | 12000-18000 | 3500-5000 | 6-9 | 12000-14000 | 1500-2000 | |
| 8mm | 10000-16000 | 4000-7000 | 8-12 | 10000-16000 | 4000-7000 | 8-12 | 10000-12000 | 1500-2000 | |
| 10mm | 10000-14000 | 6000-9000 | 10-15 | 10000-14000 | 6000-9000 | 10-15 | 10000-12000 | 1800-2200 | |
| 12mm | 8000-12000 | 6000-9000 | 12-18 | 8000-12000 | 6000-9000 | 12-18 | 8000-10000 | 1800-2200 | |
| 14mm | 7000-10000 | 6000-9000 | 12-18 | 7000-10000 | 6000-9000 | 12-18 | 6000-7000 | 1800-2200 | |
| 16mm | 7000-9000 | 6000-9000 | 12-18 | 7000-9000 | 6000-9000 | 12-18 | 6000-7000 | 1800-2300 | |
| 18mm | 6000-8000 | 6000-8000 | 12-18 | 6000-8000 | 6000-8000 | 12-18 | 6000-7000 | 1800-2300 | |
| 20mm | 6000-8000 | 6000-8000 | 12-18 | 6000-8000 | 6000-8000 | 12-18 | 5000-7000 | 1800-2300 | |
| Application Notes: | |||||||||
| • Compressed air cooling is strongly recommended when machining acrylic to prevent melting and chip adhesion. | |||||||||
| • Compressed air or mist cooling is strongly recommended for aluminium and copper to avoid built-up edge. | |||||||||
| • If tool burning, chip welding, or vibration occurs, reduce spindle speed or cutting depth first. | |||||||||
| • When actual cutting depth significantly exceeds the recommended value, start machining at a lower feed rate. | |||||||||